數控切割機在實現切割加工時為了降落資料損耗，須要對切割整機予以排版，類似的步驟在采取套料軟件實現時，因為很多用戶接觸數控行業的時光都不長，因此對這一具體的操作好不太理解；下面帶你一起來具體剖析：

設置外邊界引入線位置處所。個別來說這是考慮熱變形跟外面行走方向之間的關連。對于假設切割起始位置處所是{左下}，其外邊界引入線位置處所為{右下},切割位置處所起始位置處所為，則外邊界引入線位置處所為點擊修改死板參數；設置整機與整機之間間隔的值(個別為1倍割縫值巨細)，決定公共邊里的公共邊套料，判斷加載/幻化板材尺寸、加載整機并對整機截至排列；輸出NC；校驗、檢查共邊整機的切割點及行走線路。判斷無誤后，就興許送去切割機平臺截至切割了；在加載整機前必須決定公共邊套料，否則會呈現無奈共邊；在修改設置文件典范模范里的削減穿孔選項時，要從新對公共邊套料截至決定；在利用共邊的效歷時要留心；引入線的位置處所跟將來所產生的行走方向與熱變形的關聯。